Quick Answer: Do Drywall Seams Have To Be On A Stud?

Why can’t I find a stud in my wall?

Move left to right tapping on the wall and when you hear a different pitch that’s likely the stud.

A third method is to use a strong magnet to locate the nail or screws holding the drywall to the studs.

You can knock on the wall to find the general stud location then confirm using the magnet..

Why do stud finders never work?

Most magnet type stud finders don’t work effectively since they are dependent on locating the fasteners (screws) used to secure the drywall and they can be very difficult to locate.

How do I estimate a drywall job?

I usually measure out the total square footage that needs to be drywalled and charge between $1.25-1.50 a sq/ft depending how big the room is the bigger the room the cheaper the price works out to about $40 or higher a sheet to hang, mud and sand.

Do all drywall have studs?

Studs exist to hold up drywall on interior walls and wood sheathing on exterior walls. This means you will always find a stud, header, or footer on the top, bottom, or corners of walls.

How big a gap can you fill with drywall mud?

You can usually fill gaps less than 1/2 inch wide with joint compound while you are taping, but joint compound cracks when used to fill wider gaps. The solution is to fill the gaps with patching compound or, if they are especially wide, with strips of drywall.

Does it matter if you drywall ceiling or walls first?

Hang drywall on the ceiling first, then the walls. Check the ceiling for bowed joists using a 4-ft. level. Irregularities less than 1/8 in.

Is mesh or paper tape better for drywall?

Conclusion. In general, paper drywall tape is slightly stronger and more versatile, but mesh tape has a more manageable learning curve and better moisture resistance. At the end of the day, this contest comes down to personal preference: use the tape that you’re most comfortable with!

How do you hide bad drywall seams?

There is no easy way to combat a drywall seam, so, here are 10 clever ways to hide them:Apply a skim coat of setting compound.Use drywall tape.Sand the seam.Use dark or matte paint.Hanging up wall décor.Color washing technique.Use paper tape.Use better drywall mud.More items…

What can I use instead of drywall tape?

Mesh Tape. Fiberglass mesh tape offers a few advantages. First, it is easy to use. Just tear a piece off the roll and lay it on a layer of wet joint compound.

Should drywall be butted tight?

10 Answers. It really doesn’t matter, I would run them tight, it uses less mud. If a gap occurs, don’t sweat it. It is better to run drywall tight into the corners, it makes taping easier than having a gap.

Is it better to hang drywall vertical or horizontal?

On commercial jobs, fire codes often require seams to fall on the entire length of the framing, so the drywall must be hung vertically. However, on residential jobs, the drywall on the walls is typically hung horizontally. For walls nine feet high or shorter, hanging the drywall horizontally has a number of benefits.

How do you mount a TV on drywall without studs?

To install the brand new Echogear drywall TV mount, you’ll just need to complete 3 simple steps.Attach brackets to the back of your TV. Some TV mounts don’t come with the hardware to attach to all TVs. … Nail The Wall Plate Into The Drywall. This is the fun part. … Attach The TV To The Wall Plate.

Should drywall touch the floor?

Always leave a 1/2-inch gap at the floor. This allows for floor and wall expansion without cracking the drywall. It also helps prevents moisture wicking if the floor floods.

Can you use 1/2 inch drywall ceiling?

Building codes do, have some requirements when it comes to the thickness of drywall panels. … 1/2-inch: Half-inch drywall panels are the standard thickness for interior walls, as well as ceilings. 5/8-inch: These panels are commonly used for ceilings, or for walls that require a prescribed fire-resistant rating.

How much gap should be between sheets of drywall?

However, during installation, be religious about keeping that 1/8-inch space between sheets by using a guide. The blade of a drywall square is about 1/8-inch thick and does the trick.

What happens if you don’t tape drywall seams?

Drywall tape does not offer an mechanical strength at all. If you skipped the drywall tape and just used joint compound to fill in the seams, the seams would become visible again after the compound dried. Joint compound shrinks!

Can you end drywall not on a stud?

Yes, you need to start and stop drywall on a stud. Every edge of the sheetrock needs to be supported continuously. Cut the sheetrock down so it’s edge is in the middle of a stud. Try to put your cut edge in a corner because the factory edges are tapered so when you tape and mud it ends up flat.